News Centre

Send your inquiry

Chemical Processing Plants: Engineering Plastics for Tanks, Linings & Scrubbers - cover image

Chemical Processing Plants: Engineering Plastics for Tanks, Linings & Scrubbers

Material Map for Chemical Plant Duty

Equipment

Typical Plastics

Selection Driver

Storage tanks & vessels

PVDF, PP, HDPE, FRP-lined

Media compatibility, temperature

Tank & pipe linings

PTFE, PVDF, PP

Permeation resistance, thermal cycling

Scrubbers & ducting

PP, PVDF, PVC

Acid vapour, temperature limits

Process piping

PVDF, PP, PTFE-lined

Pressure, chemical, weldability

Pump & valve internals

PEEK, PTFE, PVDF

Wear plus chemical attack

Seals & gaskets

PTFE, filled PTFE

Widest chemical window

 

How Material Selection Actually Works

· Identify the full chemical spectrum — not just the process fluid, but cleaning agents and upset conditions

· Confirm concentration, since dilute and concentrated forms of the same chemical behave differently

· Establish the maximum temperature, including excursions and cleaning cycles

· Check pressure and whether the part is load bearing as well as chemically exposed

· Review permeation data for lined equipment, not just chemical resistance ratings

· Account for thermal cycling between ambient and process temperature

ngm k6b esdpeek photoroom

The Limits Nobody Mentions in the Datasheet

Two failure modes catch out even experienced plant engineers. The first is permeation: a liner can be chemically resistant to a fluid and still allow it to permeate through to the substrate, causing corrosion from behind. The second is environmental stress cracking, where a chemical that is nominally compatible attacks a part that already carries assembly or thermal stress. Both are design problems, not material problems, and both are solved by allowing for movement, reducing residual stress, and specifying thicknesses based on permeation rates rather than mechanical strength alone.

Why Plastics Displace Lined Steel

A rubber-lined or glass-lined steel vessel is heavy, expensive to fabricate, and difficult to repair: a single lining defect becomes a corrosion site that spreads behind the lining. Solid thermoplastic construction avoids that failure mode entirely, because there is no interface to fail. Polymer vessels and pipework are also quicker to install, easier to modify on site, and transparent or translucent in some grades, letting operators see liquid levels directly. The trade-off is temperature and pressure capability, which is why plastics dominate the lower-temperature, moderate-pressure end of chemical processing and remain secondary in high-pressure reactors.

Specification Checklist

· Request chemical resistance data at your actual concentration and temperature

· Ask for permeation data for any lining or lined vessel

· Specify welding and fabrication standards, including welder qualification

· Include a documented cleaning regime in the material compatibility review

· Plan for inspection access to liners and welds

· Keep batch traceability records for safety-related components

 

Related reading: PVDF Sheet Guide, PEEK Chemical Resistance Chart, and Engineering Plastics for Pumps, Valves & Seals.

ngm k6b esd peek sheet (5)

FAQ

Q1: Which plastic is best for chemical storage tanks?

It depends on the medium: PVDF and PTFE for the widest resistance, PP and HDPE for cost-effective general duty. Chemical resistance data at the actual concentration and temperature decides the answer.

Q2: What is permeation and why does it matter?

Permeation is the diffusion of a chemical through a plastic wall. A liner can be chemically resistant and still allow vapour to reach the steel behind it, causing hidden corrosion.

Q3: Why do plastic-lined vessels fail?

Usually through lining defects, thermal cycling, or permeation rather than chemical attack of the liner itself. Reducing stress and allowing thermal movement prevents most cases.

Q4: Can plastics be used in scrubbers?

Yes — PP and PVDF are standard for acid scrubbers and ducting where steel would corrode rapidly, subject to temperature limits.

Q5: How do I verify chemical compatibility?

Check resistance charts at your specific concentration and temperature, request immersion test data for the grade, and test a sample component in the real process before committing to a full installation.

Specifying materials for chemical plant equipment? Contact NAGOMER for PVDF, PTFE, PEEK, and PP components with full material documentation.

────────────────────────────────────────

NAGOMER — Professional Engineering Plastics Solutions

www.nagomer.com  |  info@nagomer.com

滚动至顶部

Inquiry form