News Centre

Send your inquiry

Flame Retardant Engineering Plastics: UL94 Ratings & Fire Safety Guide - cover image

Flame Retardant Engineering Plastics: UL94 Ratings & Fire Safety Guide

Understanding UL94 Ratings

Rating

Behaviour

Typical Use

HB

Slow horizontal burn

General-purpose, low-risk

V-2

Vertical burn, drips allowed

Consumer electronics

V-1

Vertical burn, no flaming drips

Appliances, enclosures

V-0

Vertical burn, self-extinguishing in 10s

Electrical, EV, industrial

5VB / 5VA

Very severe, 5VA no hole in plaque

High-risk enclosures

 

Ratings are thickness dependent: a material rated V-0 at 1.5 mm may only achieve V-2 at 0.8 mm. Always specify the rating together with the wall thickness it was tested at.

Materials That Are Inherently Flame Retardant

· PEEK — UL94 V-0 without additives, low smoke and toxic gas emission

· PPS — V-0 inherently, excellent for electrical and automotive

· PEI (ULTEM) — V-0, plus low smoke for transport interiors

· PTFE and PVDF — V-0, excellent for chemical and electrical duty

· PSU / PPSU — V-0 to V-1 depending on thickness, transparent options

ngm k12b peek rod (1)

Materials That Need Additives

Polyamide, POM, PC, and polyolefins generally need flame retardant packages to reach V-0. Traditional halogenated systems are effective but raise smoke toxicity concerns; modern formulations favour phosphorus-based, melamine, or mineral fillers such as aluminium trihydroxide. Each approach carries trade-offs: mineral fillers reduce mechanical strength, phosphorus systems can affect hydrolytic stability, and halogen-free grades often cost more. POM is notoriously difficult to flame retard and is usually replaced outright where V-0 is mandatory.

Beyond UL94: Smoke, Toxicity and System Standards

UL94 measures ignitability in a small-scale bench test. Transport and building applications usually require more: EN 45545 for rail, NFPA 130 for transit tunnels, and FAR 25.853 for aircraft interiors all evaluate flame spread, heat release, smoke density, and smoke toxicity together. Materials such as PEI and PEEK, which combine inherent flame retardancy with low smoke emission, are common choices where these combined requirements apply. In sealed electrical enclosures the practical question is often whether a fire can spread and whether the escaping gases are hazardous — not simply whether a small sample self-extinguished. NAGOMER supplies inherently flame-retardant grades and can advise on documentation for compliance submissions.

Related reading: Engineering Plastic Certifications Explained, PPS GF40 Sheet Guide, and Engineering Plastics in Aerospace.

pei 副本

FAQ

Q1: What does UL94 V-0 mean?

A vertically mounted specimen self-extinguishes within 10 seconds after two 10-second flame applications, with no burning drips that ignite cotton below. It is the most common requirement for electrical housings.

Q2: Which engineering plastics are inherently V-0?

PEEK, PPS, PEI, PTFE, and PVDF achieve V-0 without flame retardant additives, which is why they are preferred where smoke toxicity also matters.

Q3: Is UL94 the same as EN 45545?

No. UL94 is a small-scale ignitability test; EN 45545 is a system-level railway standard that also evaluates flame spread, smoke density, and toxicity. A UL94 V-0 material may still fail EN 45545 at a given hazard level.

Q4: Can POM be made flame retardant?

Only with difficulty, and usually with significant loss of properties. Where V-0 is required, POM is normally replaced with PPS, PBT, or PEEK.

Q5: Do flame retardants affect mechanical properties?

Yes — mineral fillers reduce strength and impact resistance, and phosphorus systems can influence hydrolytic stability. Always verify mechanical data on the specific flame-retardant grade, not the base polymer.

Need flame-retardant materials with documentation? Contact NAGOMER for inherently V-0 grades and machined components for electrical, EV, and transport projects.

────────────────────────────────────────

NAGOMER — Professional Engineering Plastics Solutions

www.nagomer.com  |  info@nagomer.com

滚动至顶部

Inquiry form