News Centre

Send your inquiry

Industrial 3D Printing with Engineering Plastics: PEEK, PEI and PPSU - cover image

Industrial 3D Printing with Engineering Plastics: PEEK, PEI and PPSU

The Industrial Material Portfolio

Material

Print temp.

Strength

Typical printed use

PLA / PETG

200–250°C

Low

Jigs, fixtures, concept models

PA-CF

260–290°C

Moderate

Functional brackets, tooling, drone frames

PC

270–300°C

Good

Housings, transparent parts, ducts

PEI (ULTEM)

360–390°C

High

Aerospace interior, electrical insulation

PEEK

380–420°C

High

Medical, chemical, high-temperature duty

PPSU

370–400°C

High

Sterilisable medical and food-contact parts

 

Process Control Determines Properties

A printed part is not isotropic. Strength along the extrusion path typically exceeds strength across layer boundaries by a factor of two or more, so a bracket loaded across its layers can fail at a fraction of the datasheet value. High-performance materials demand more than a hot nozzle: an actively heated chamber near 200°C for PEEK, controlled cooling, and a drying regime that keeps moisture below a few hundred parts per million. Moisture in PEEK at print temperature causes hydrolysis, visible as bubbling, voids, and a sharp drop in elongation.

k12n (19)

Annealing and Post-Processing

· Anneal printed PEEK and PEI to relieve layer stress and raise crystallinity

· Crystallinity in PEEK affects chemical resistance and wear — annealing is not cosmetic

· Machine critical bores, sealing faces, and mating surfaces after printing

· Printed surfaces are rougher than moulded ones; plan for finishing on sealing interfaces

· Do not assume printed holes are round — drill or ream them

· For medical and food contact, verify the specific feedstock certification, not just the polymer family

 

Where Printing Beats Machining

Printing wins where geometry is complex, volumes are low, or internal channels are needed. Conformal cooling, lattice-filled brackets, integrated ducts, and lightweight ribs are cheap to print and expensive to machine. Machining wins where the material is brittle, the tolerance is tight, the surface must seal, or the part is simple enough that a stock shape is faster. In practice most high-performance parts are hybrid: printed near-net, then machined on the critical features.

Sourcing the Material

Printed part quality is limited by filament or pellet quality and by consistent diameter. For high-temperature polymers, certified feedstock with documented drying and lot traceability matters more than printer brand. NAGOMER supplies PEEK, PEI, PPSU, and PA stock shapes for machined parts and for hybrid printed-and-machined components, and can advise on where a machined solution is simpler than an additive one.

Related reading: Injection Moulding vs Machining Plastic Parts, Plastics for Aerospace Interiors and Brackets, and PPSU vs PEI vs PC Transparent High-Temperature Plastics.

pc+abs (15)

FAQ

Q1: Is printed PEEK as strong as machined PEEK?

In the layer direction it can approach it, but across layers strength is typically 50–70% of the machined value. Annealing and good process control narrow the gap.

Q2: Why does high-temperature filament need drying?

Absorbed moisture vaporises at print temperature, causing voids, bubbles, and hydrolysis that reduces molecular weight and elongation.

Q3: Can printed parts be sterilised?

PPSU and PEI printed parts can be autoclaved if porosity is controlled and the feedstock is qualified for the sterilisation cycle.

Q4: Which materials print on standard machines?

PLA, PETG, and PA-CF print on heated-bed machines. PEEK, PEI, and PPSU require machines with 200°C chamber capability and all-metal hotends.

Q5: Should critical features be printed or machined?

Machine them. Bores, seal faces, and mating surfaces are best printed oversize and finished by machining.

Comparing printed and machined options? Ask NAGOMER for a material and process recommendation.

────────────────────────────────────────

NAGOMER — Professional Engineering Plastics Solutions

www.nagomer.com  |  info@nagomer.com

滚动至顶部

Inquiry form