News Centre

RESOURCES

Send your inquiry

Failure Analysis of Engineering Plastic Parts: Cracking, Wear & Chemical Attack - cover image

Failure Analysis of Engineering Plastic Parts: Cracking, Wear & Chemical Attack

When a plastic component fails in service, the instinct is to blame the material. In most cases the material performed exactly as specified — the failure came from stress, environment, or geometry that the design did not account for. Learning to read a failed plastic part is one of the most valuable skills in material engineering, and it usually saves money faster than switching polymers.

Engineering Plastics for Shipbuilding & Marine Engineering - cover image

Engineering Plastics for Shipbuilding & Marine Engineering

Seawater destroys metal through corrosion, pitting, and galvanic attack — which is exactly why modern ships carry so much polymer. Engineering plastics serve in seawater cooling systems, deck hardware, stern bearings, and wear components, delivering service lives that painted steel cannot match. This guide covers the materials and the marine-specific challenges they must survive.

Plastics for Rail & Mass Transit: EN 45545 Fire Safety Compliance - cover image

Plastics for Rail & Mass Transit: EN 45545 Fire Safety Compliance

Railway interiors are among the most tightly regulated environments for materials: a fire in a tunnel must not spread, must not fill the carriage with smoke, and must not produce toxic gases. EN 45545 codifies these requirements across Europe, and similar regimes apply worldwide. This guide explains how the standard works and which engineering plastics satisfy it.

Thermally Conductive Plastics: Materials for Heat Management - cover image

Thermally Conductive Plastics: Materials for Heat Management

Standard engineering plastics are thermal insulators at roughly 0.2–0.3 W/m·K, which is why they are used for insulation and handles. Add the right fillers, though, and the same materials become heat conductors — electrically insulating or electrically conductive as required — while remaining injection mouldable and far lighter than aluminium. This guide explains what thermally conductive plastics can and cannot do.

Creep & Stress Relaxation: Designing Plastic Parts for Long-Term Load - cover image

Creep & Stress Relaxation: Designing Plastic Parts for Long-Term Load

A plastic part that passes every short-term test can still fail in service — slowly, quietly, and years later. Creep and stress relaxation are the reason. Unlike metals, polymers continue to deform under sustained load, and a joint that is tight today may loosen within months. Understanding these two behaviours is the difference between a design that lasts and one that returns as a warranty claim.

Flame Retardant Engineering Plastics: UL94 Ratings & Fire Safety Guide - cover image

Flame Retardant Engineering Plastics: UL94 Ratings & Fire Safety Guide

Fire safety requirements decide material selection in more projects than most engineers expect — from electrical enclosures and EV battery packs to railway interiors and data-centre hardware. The question is rarely simply “is it flame retardant?” but which standard applies, what rating is required, and whether the material achieves it inherently or through additives. This guide explains the ratings and the materials that meet them.

PAI (Torlon) vs PEEK: Choosing for Extreme Wear and High Temperature - cover image

PAI (Torlon) vs PEEK: Choosing for Extreme Wear and High Temperature

When PEEK reaches its limits — very high loads, very high PV values, or temperatures above 250°C — PAI (polyamide-imide, familiar as Torlon) is the next step up the performance ladder. It is the strongest engineering plastic in common industrial use, with outstanding wear behaviour, but it has its own vulnerabilities. This guide compares the two so you can specify with confidence.

PBT Sheet & Rod: Properties, Processing & Applications Guide - cover image

PBT Sheet & Rod: Properties, Processing & Applications Guide

PBT (polybutylene terephthalate) is the engineering polyester behind countless electrical connectors, sensor housings, and automotive components. It combines fast crystallisation and excellent electrical properties with low moisture uptake and good chemical resistance — and unlike polyamide, it keeps its dimensions when the weather changes. NAGOMER supplies PBT stock shapes and machines components for electrical, automotive, and industrial customers.

POM-C vs POM-H: Copolymer or Homopolymer — Which Acetal Should You Choose? - cover image

POM-C vs POM-H: Copolymer or Homopolymer — Which Acetal Should You Choose?

POM is the most widely used precision engineering plastic, but it comes in two distinct chemistries: homopolymer (POM-H, the original Delrin-type acetal) and copolymer (POM-C). They look identical, machine similarly, and cost about the same — yet they fail differently, and choosing the wrong one quietly shortens part life. This guide explains the real differences and when each belongs in your design.

Plastic Fasteners, Screws & Threads: Design Guide for Engineering Plastics - cover image

Plastic Fasteners, Screws & Threads: Design Guide for Engineering Plastics

Plastic screws solve two problems at once: they cannot corrode, and they never create a galvanic couple with the plastic parts they hold. They also behave differently from metal fasteners — torque limits are far lower, thread engagement must be deeper, and thermal expansion changes clamp load. NAGOMER machines PEEK, PVDF, and PA fasteners and threaded components for chemical, medical, and electronics applications.

滚动至顶部

Inquiry form