News Centre

Send your inquiry

Plastics for Agriculture & Irrigation: Materials That Survive the Field - cover image

Plastics for Agriculture & Irrigation: Materials That Survive the Field

Material Map for Agricultural Duty

Component

Material

Key Requirement

Irrigation pipe & fittings

PE, PA12, PVDF

UV resistance, pressure, fertiliser compatibility

Valve seats & seals

PEEK, filled PTFE

Chemical resistance, wear, no corrosion

Sprayer nozzle bodies & pumps

PPS, POM, PVDF

Agrochemical resistance

Slurry & soil wear parts

UHMW-PE, PA cast

Abrasion and impact resistance, low friction

Greenhouse guides & rollers

UHMW-PE, POM

Low friction, UV stable grades

Machine bushings & bearings

PEEK composites, POM

Dust tolerance, lubrication-free

 

The UV Problem in Open Fields

Ultraviolet exposure in agriculture is relentless, and most polymer failures in the field are UV related rather than mechanical. Polypropylene, polyethylene, and polyamide all need stabilisation, and carbon black is the cheapest effective solution — which is why so much agricultural plastic is black. PVDF and PTFE are inherently UV stable and need no additives, while PEEK and POM should always be specified in black grades for outdoor duty. A part that would last twenty years indoors can fail in three seasons in a field without UV protection, so material choice and colour are equally important specification decisions.

防静电 peek

Agrochemicals Are Not Just Water

· Nitrogen fertilisers — concentrated salt solutions accelerate hydrolysis in PA and PBT

· Ammonia-based products — attack polyamide and POM over time

· Pesticide and herbicide carriers — often solvent-based, requiring PVDF or PTFE

· Soil pH extremes — considered for buried components in contact with soil chemistry

· Manure slurry — mildly acidic, abrasive, and biologically active

 

Design for Field Service

· Standardise fasteners and fittings so repairs need no specialist tools

· Design for replacement of wear parts rather than whole assemblies

· Allow generous clearances for dust and grit ingress

· Protect seals from direct spray and soil contact

· Choose black, UV-stabilised grades for all exposed components

· Keep spare-part profiles simple enough to machine on site

 

Why Plastics Beat Metal Outdoors

A steel irrigation component may be cheaper at purchase and more expensive by the second season. Galvanised fittings corrode once the coating is scratched; filters pit; and any component that sits in fertiliser solution is on borrowed time. Polymer components do not corrode, they absorb impact from field operations, and they can be replaced by the operator. The economics shift further when downtime is counted: a failure during irrigation scheduling can cost a crop, not just a part. That is why agricultural manufacturers increasingly specify engineering plastics in high-wear, high-exposure positions even where metal would be cheaper up front.

Related reading: UV Resistance & Outdoor Weathering, UHMW-PE Sheet Guide, and Cast Nylon & PA12 Guide.

esd pa sheet (7)

FAQ

Q1: Which plastics survive UV exposure outdoors?

PVDF and PTFE are inherently UV stable. Others need protection — carbon black is the cheapest and most effective, which is why agricultural plastics are typically black.

Q2: Can plastic irrigation fittings handle fertiliser?

Yes, provided the material is matched to the chemistry. PE and PVDF handle most fertiliser solutions; polyamide is vulnerable to concentrated nitrogen solutions and ammonia.

Q3: What is the best material for soil-engaging wear parts?

UHMW-PE for sliding wear and impact, and cast nylon for higher-load structural parts. Both resist abrasion and do not corrode in soil.

Q4: Do plastic parts need replacement more often than metal?

In abrasive and corrosive duty, usually less often — and they can be replaced on site rather than requiring workshop fabrication.

Q5: How can I extend the life of plastic field components?

Choose black UV-stabilised grades, allow for soil ingress in clearances, and design wear parts to be replaced individually.

Specifying components for agricultural equipment? Contact NAGOMER for UV-stable, chemical-resistant parts machined to drawing.

────────────────────────────────────────

NAGOMER — Professional Engineering Plastics Solutions

www.nagomer.com  |  info@nagomer.com

滚动至顶部

Inquiry form