News Centre

Send your inquiry

Plastics for Elevators & Escalators: Wear Parts and Compliance - cover image

Plastics for Elevators & Escalators: Wear Parts and Compliance

Components and Material Choices

Component

Material

Requirement

Escalator handrail guides

UHMW-PE, POM

Very low friction, wear resistance, no lubrication

Step & pallet rollers

POM, PA, PU

High cycle life, quiet running, load capacity

Elevator door rollers & guides

POM, PA, UHMW-PE

Smooth travel, dimensional stability

Guide shoes & gibs

POM, PET-P, PEEK

Sliding wear at speed, low noise

Safety gear & brake linings

PEEK composites

Friction control, heat resistance

Buffer & impact components

PA, PU

Energy absorption without cracking

 

Silence and Comfort Are Specification Criteria

A public escalator or elevator is judged by how it sounds and feels. Metal-on-metal guides transmit vibration and produce the characteristic rattle that passengers notice immediately; polymer guides damp it. The 20–30% cost premium over a bronze or steel component is routinely justified on noise and comfort alone, before wear life is even considered. In practice, engineers treating quietness as a hard specification find that it translates directly into longer component life, because damping and low friction go together — vibration is energy, and energy that is not dissipated as noise is usually being dissipated as wear.

petp (11)

Lubrication-Free Operation and Public Safety

Public installations increasingly forbid oil or grease in positions where residue could mark clothing or create slipping hazards. Self-lubricating POM, PET-P, and PEEK components remove that entire concern, along with the maintenance visits required to re-lubricate them. Fire performance also matters: components in public buildings are frequently subject to national fire safety requirements, and grades with documented flame retardancy may be required in enclosed spaces. Where the component is safety-critical, material consistency over decades matters more than peak performance, which is why stable, well-characterised grades are preferred over exotic formulations.

Design Points for Long Service

· Size for wear allowance, not just initial fit — pick a grade that can be re-faced

· Avoid sharp edges on guides that contact handrails or ropes

· Design rollers for replacement without dismantling the whole assembly

· Confirm fire performance requirements for the specific building type

· Test at the actual load and speed — cycle life does not scale linearly

· Prefer machined parts over small-volume mouldings for spare parts support

 

Spares and Long-Term Support

Lift and escalator equipment stays in service for twenty years or more, often well beyond the production life of the original component. Machined polymer parts solve this elegantly: a roller or guide profile can be reproduced from drawing or sample decades later, without the tooling investment that injection moulding would require. That is a genuine engineering consideration, not just a commercial one, and it is why original equipment manufacturers increasingly specify machined stock shapes for low-volume and spare-part positions. NAGOMER machines lift and escalator components from POM, PET-P, UHMW-PE, and PEEK to drawing or sample.

Related reading: Bearings & Bushings Material Selection, POM-C vs POM-H Comparison, and UHMW-PE Sheet Guide.

esd pom sheet ngm m6 (18)

FAQ

Q1: Which plastic is used for escalator handrail guides?

UHMW-PE and POM, chosen for very low friction, wear resistance, and the ability to run without lubrication in continuous service.

Q2: Why are plastic rollers used in elevators?

They run quietly, need no lubrication, resist corrosion, and damp vibration far better than metal rollers.

Q3: Do lift components need to be flame retardant?

Requirements vary by building type and jurisdiction. Confirm the applicable national fire safety requirements for the installation before finalising material selection.

Q4: How long do plastic guide components last?

Typically several years of continuous public service, with replacement driven by measured wear rather than a fixed calendar interval.

Q5: Can spare parts still be sourced after production ends?

Machined polymer components can be reproduced from drawing or sample indefinitely, which avoids the tooling problems associated with obsolete mouldings.

Manufacturing or maintaining lift and escalator equipment? Contact NAGOMER for machined POM, PET-P, UHMW-PE, and PEEK components to drawing.

────────────────────────────────────────

NAGOMER — Professional Engineering Plastics Solutions

www.nagomer.com  |  info@nagomer.com

滚动至顶部

Inquiry form