News Centre
News Type
Send your inquiry
Plastics for Hydraulic and Pneumatic Systems: Seals, Rings and Guides
Component and Material Map
Component | Material | Key requirement |
Rod & piston seals | PU, filled PTFE, NBR | Low friction, extrusion resistance |
Back-up rings | PEEK, filled PTFE, POM | Anti-extrusion at high pressure |
Wear rings / guide bands | PTFE bronze, PEEK, fabric-reinforced | Load bearing, low friction |
Piston & rod guides | POM, PA, PEEK | Dimensional stability, wear |
Scraper / wiper | PU, POM | Abrasion resistance, dirt exclusion |
Valve seats & poppets | PEEK, PPS, POM | Sealing, chemical resistance |
Pneumatic fittings | PA12, PBT, POM | Toughness, dimensional accuracy |
Pressure, Velocity and the PV Limit
Seal and wear-ring materials are limited by the product of contact pressure and sliding velocity. PTFE compounds have the widest chemical and temperature range but cold flow under sustained load, which is why they are almost always backed by PEEK or POM rings at high pressure. PEEK tolerates high PV with good creep resistance but is abrasive against soft counterfaces and costly. POM sits between, offering good wear and machining ease for guides and wipers. Exceeding the PV limit does not fail immediately — it produces accelerated wear, heat, and eventual seal extrusion, often mistaken for a fluid problem.
Fluid Compatibility
· Mineral oil: most engineering plastics are compatible; verify additive package for aggressive EP oils
· Water-based and HFA/HFC fluids: require careful selection, as water attacks PA and hydrolyses PU
· Phosphate esters and Skydrol: attack many polymers — PEEK, PTFE, and PPS are safer choices
· Biodegradable ester fluids: can swell or soften standard seals; test before commitment
· Compressed air: watch for moisture and oil carryover degrading PA tubing over time
· Temperature at the seal is usually higher than bulk fluid temperature — allow for it
Pneumatic Specifics
Pneumatic systems run dry, which changes the wear mechanism: no fluid film separates the surfaces, so friction and wear become dominant. PA12 and PBT dominate fittings and tubing because of toughness, dimensional accuracy, and low moisture uptake. POM works well for valve bodies and spools where machining and low friction both matter. In dry-running pneumatic valves, filled PTFE and PEEK seats provide long life where an unfilled polymer would wear rapidly.
Failure Modes to Design Against
· Extrusion — seal nibbles into the clearance gap under pressure; solve with back-up rings
· Cold flow — PTFE creeping under sustained load; solve with filled grades or PEEK
· Thermal expansion mismatch causing seizure in tight bores
· Contamination embedding in soft seals and scoring the rod
· Hydrolysis of PU in water-based fluids
· Chemical swelling closing clearances and increasing friction
Related reading: Engineering Plastics for Pumps Valves and Seals, Plastics for Oil-Free Compressors, and Machining Engineering Plastics.
FAQ
Q1: What is the best material for hydraulic wear rings?
Filled PTFE with bronze or carbon/graphite for low friction, or PEEK where higher loads and temperatures apply. Both are commonly used together.
Q2: Why do PTFE seals need back-up rings?
PTFE cold flows under pressure and extrudes into the clearance gap. A PEEK or POM back-up ring prevents it.
Q3: Which plastic suits pneumatic fittings?
PA12 and PBT are standard because of toughness, accurate moulding, and low moisture absorption.
Q4: What happens if the PV limit is exceeded?
Wear accelerates rapidly, generating heat that softens the polymer and leads to seal extrusion and leakage.
Q5: Are standard seals compatible with biodegradable hydraulic fluid?
Not always. Ester-based fluids can swell or soften conventional compounds, so compatibility testing is required.
Designing a sealing system? NAGOMER machines wear rings, guides, back-up rings, and seats to drawing.
────────────────────────────────────────
NAGOMER — Professional Engineering Plastics Solutions
www.nagomer.com | info@nagomer.com