News Centre

Send your inquiry

Plastics for Oil-Free Compressors: Valves, Piston Rings & Seals - cover image

Plastics for Oil-Free Compressors: Valves, Piston Rings & Seals

The Dry-Running Challenge

· Piston rings and packings slide against the cylinder without oil — wear is the design limit

· Valve plates cycle millions of times at elevated temperature

· Discharge temperatures reach 150–200°C in the compression stages

· Friction heat must be removed through components that are poor thermal conductors

· Any lubricant that migrates contaminates the product gas — there is no tolerance for it

 

Component-by-Component Material Guide

Component

Recommended Material

Why

Valve plates

PEEK, PEEK CF30

Fatigue endurance at 200°C, impact resistance

Piston rings

Filled PTFE, PEEK composites

Dry wear resistance, low friction

Packing & rider rings

PEEK + PTFE + graphite

Load capacity, no stick-slip

Piston & plunger seals

Filled PTFE, PEEK

Chemical inertness to process gas

Valve seats & guards

PEEK, PPS

Impact plus temperature

Wear bands

PTFE-based composites

Controlled clearance, sacrificial wear

k12 (27)

Why PEEK Valve Plates Replaced Metal

Traditional metallic valve plates fail by fatigue fracture and by impact damage on the seat. PEEK plates changed the economics of compressor valves: their fatigue endurance at elevated temperature is outstanding, their mass is lower so they seat more gently, and they conform slightly to minor seat imperfections instead of chipping. They also resist the oil-free duty better, because their wear mechanism does not depend on a lubricant film. The result is longer valve life, fewer stops, and quieter operation — the reasons PEEK is now the default valve plate material across reciprocating compressor technology.

Ring and Packing Design

Dry-running piston rings live or die by material and geometry. Filled PTFE rings offer low friction and good conformability but creep under sustained load, so they are backed by carefully designed ring sets — radial and tangent cuts that maintain seal pressure as the ring wears. PEEK-based rings and rider bands carry higher loads and temperatures where PTFE alone would cold-flow. Cylinder surface finish matters as much as the ring: too smooth promotes adhesion, too rough accelerates abrasion. NAGOMER machines valve plates, rings, and packing sets in PEEK and filled PTFE to compressor OEM specifications.

Application Range

· Medical and laboratory air — zero oil tolerance, PEEK valves and PTFE rings throughout

· Food and beverage — contact gas purity requirements identical to medical

· Hydrogen and process gas compression — PEEK internals at elevated pressure and temperature

· Natural gas and CNG — PEEK valve plates and PTFE packings in hostile duty

· Rail and marine braking air — dry-running reliability with minimal maintenance access

 

Related reading: PEEK Filled Grades Guide, PEEK Fatigue Resistance, and Plastics for Hydrogen Energy.

Plastics for Oil-Free Compressors: Valves, Piston Rings & Seals - PTFE product photo

FAQ

Q1: Why are compressor valve plates made of PEEK?

PEEK combines fatigue endurance at 200°C with impact resistance and low mass, giving longer valve life and fewer compressor stops than metallic plates.

Q2: How do piston rings work without oil?

Filled PTFE and PEEK composites run dry against the cylinder wall, with ring geometry — not lubricant — maintaining the seal. Wear allowance is designed into the ring set.

Q3: What temperatures do oil-free compressor internals see?

Discharge temperatures typically reach 150–200°C in multi-stage machines, which is why PEEK and filled PTFE dominate the high-temperature positions.

Q4: Can PTFE rings handle high loads?

Unfilled PTFE cold-flows under load. Filled grades (glass, bronze, carbon) and PEEK-based rings carry substantially higher duty.

Q5: Which compressors need oil-free internals?

Any application where oil in the gas stream is unacceptable: medical air, food gas, hydrogen, breathing air, and laboratory or instrumentation supply.

Manufacturing oil-free compressors? Contact NAGOMER for PEEK valve plates and filled PTFE rings machined to OEM specification.

────────────────────────────────────────

NAGOMER — Professional Engineering Plastics Solutions

www.nagomer.com  |  info@nagomer.com

滚动至顶部

Inquiry form