News Centre

Send your inquiry

Plastics for Semiconductor Wet Processing and Wafer Handling - cover image

Plastics for Semiconductor Wet Processing and Wafer Handling

Wet Bench and Chemical Handling Materials

Material

Chemical resistance

Purity

Typical use

PFA

Broadest, including HF

Excellent

Wet bench tanks, lines, fittings

PTFE

Broadest

Excellent

Liners, seals, high-purity parts

PVDF

Strong acids, oxidisers

Very good

DI water lines, tank bodies, fittings

PEEK

Good, not strong oxidisers

Very good

CMP rings, wafer contacts, fixtures

PP

Moderate

Good

Lower-cost tanks and ducting

PPS

Good

Good

Structural parts in non-critical chemistry

 

Hydrofluoric acid and hot concentrated oxidisers narrow the field sharply: PFA and PTFE are the reliable choices, with PVDF acceptable for many acids but not for strong bases at elevated temperature.

Wafer Handling and CMP

Wafer carriers, end effectors, and CMP components face a different challenge: they must not scratch, must not generate particles, and must hold dimensional stability through chemical exposure. PEEK has become standard for CMP retaining rings because it resists slurry abrasion while holding flatness and does not contaminate the wafer. PPSU and PEI appear in carriers and handling hardware where toughness and dimensional stability matter more than chemical aggressiveness. Static control is also relevant — a charged carrier attracts particles, so dissipative grades are used in some handling positions.

ngm i12 (10)

Particles, Metal Ions and Outgassing

· Specify grades with low extractable metal ion content — sodium, potassium, iron, and calcium are critical

· Machining introduces contamination; parts must be cleaned and packaged for cleanroom use

· Avoid mould release agents, pigments, and fillers not qualified for the process

· Verify outgassing against the application — ASTM E595 gives TML and CVCM figures

· Consider surface finish: smoother surfaces retain fewer particles and are easier to clean

· Static dissipative grades reduce particle attraction on dry handling surfaces

 

Fabrication and Cleaning Discipline

A clean material machined on a dirty machine is not a clean part. Cutting fluids, swarf, and handling contamination must be controlled, and parts intended for the front end should be machined, cleaned, and bagged under conditions agreed with the fab. Dedicated tooling for high-purity work avoids cross-contamination from previous jobs, and final cleaning with DI water followed by controlled drying removes machining residue that would otherwise leach into process chemistry.

Selection Summary

For aggressive wet chemistry, choose PFA or PTFE. For DI water and most acids, PVDF is the cost-effective standard. For mechanical components in CMP and wafer contact, PEEK. For structural hardware away from chemistry, PPS and PEI. NAGOMER supplies semiconductor-grade PFA, PTFE, PVDF, and PEEK stock shapes with documentation, machined to drawing for wet process and handling applications.

Related reading: Plastics for Semiconductor Test and Burn-in Sockets, PFA and FEP Fluoropolymer Guide, and Vacuum Systems Outgassing and Material Selection.

ngm k12b (4)

FAQ

Q1: What material is used for wet bench tanks?

PFA, PTFE, and PVDF are standard. PFA is preferred where hydrofluoric acid or hot oxidisers are present.

Q2: Why is PEEK used for CMP retaining rings?

It resists slurry abrasion, holds flatness, and does not introduce metal contamination to the wafer.

Q3: How is cleanliness specified for semiconductor plastics?

Through extractable ion levels, particle counts, outgassing data such as ASTM E595, and agreed cleaning and packaging procedures.

Q4: Can PVDF handle hydrofluoric acid?

PVDF has limited resistance to HF; PFA and PTFE are the reliable choices for HF service.

Q5: Does machining contaminate high-purity parts?

Yes, through cutting fluid and swarf. Parts must be cleaned and packaged to an agreed cleanroom procedure after machining.

Specifying high-purity components? NAGOMER supplies semiconductor-grade fluoropolymers and PEEK to drawing.

────────────────────────────────────────

NAGOMER — Professional Engineering Plastics Solutions

www.nagomer.com  |  info@nagomer.com

滚动至顶部

Inquiry form