News Centre

Send your inquiry

Thermally Conductive Plastics: Materials for Heat Management - cover image

Thermally Conductive Plastics: Materials for Heat Management

How Conductivity Is Achieved

· Ceramic fillers — boron nitride (BN) and aluminium nitride (AlN) give conductivity with electrical insulation

· Alumina (Al2O3) and aluminium hydroxide — lower cost, moderate conductivity, insulating

· Graphite and carbon fibre — highest conductivity, but electrically conductive

· Metallic fillers — effective but heavy and prone to corrosion

· Typical achievable range: 1–3 W/m·K insulating grades, up to 10–20 W/m·K conductive grades

 

For context: unfilled plastic is around 0.25 W/m·K and aluminium is about 200 W/m·K. Conductive plastics close part of that gap, but they do not replace metal in high-flux cooling — they replace insulators where some heat spreading is needed.

Where Thermally Conductive Plastics Win

Application

Why Use Plastic

Typical Grade

LED heat spreaders & housings

Complex moulded geometry, electrical isolation

PA or PPS + ceramic filler

EV battery module spacers

Insulation plus heat transfer, light weight

PA + BN, flame retardant

Power electronics housings

Integrated cooling paths, no metal corrosion

PPS, PBT + ceramic

Motor & transformer bobbins

Insulation with heat dissipation

PA46, PPS + AlN

Sensor encapsulation

Direct potting around hot components

Epoxy-like grades, PPS

ngm sg12 pps sheet bk (1)

The Anisotropy Question

Filled plastics conduct heat unevenly: a moulded part conducts far better in the flow direction than across it, often by a factor of two or more. This matters enormously for design. A heat-spreader designed on a single isotropic conductivity figure may underperform badly in reality. Request directional data, and orient the part in the mould so the high-conductivity direction aligns with the intended heat path. For machined prototypes from extruded stock, conductivity follows the extrusion direction, which is worth noting when correlating test results with moulded production.

Design Guidelines

· Thin, wide sections spread heat better than thick, narrow ones

· Add metal inserts where heat must move a long distance to a sink

· Use thermal interface materials at joints — microscopic air gaps destroy performance

· Balance conductivity against mechanical properties, which fall as filler content rises

· Confirm UL94 rating if the application is electrical or EV

 

When Metal Is Still the Answer

Above roughly 3 W/m·K, filled plastics become expensive, brittle, and difficult to process, and the economics rarely beat a simple aluminium heatsink. The honest use case for thermally conductive plastics is where electrical insulation is mandatory, where complex geometry would be costly to machine in metal, where weight matters, or where corrosion and galvanic issues rule metal out. If none of those apply, a metal solution will usually be cheaper and better. NAGOMER supplies stock shapes and machined components in conventional grades for designers exploring conductive options before committing to tooling.

Related reading: Engineering Plastics for New Energy (EV Battery & Solar), PPS GF40 Sheet Guide, and PBT Sheet & Rod Guide.

sg12b (2)

FAQ

Q1: How conductive can plastic be made?

Electrically insulating grades typically reach 1–3 W/m·K. Electrically conductive graphite or carbon-filled grades can exceed 10 W/m·K, still an order of magnitude below aluminium.

Q2: Are thermally conductive plastics electrically insulating?

Ceramic-filled grades are — boron nitride and aluminium nitride conduct heat without conducting electricity. Graphite and metal-filled grades are electrically conductive.

Q3: Can thermally conductive plastic replace aluminium heatsinks?

Only for lower heat flux and where insulation, geometry, or weight justify the cost. For high-flux cooling, metal remains superior.

Q4: Why does conductivity differ by direction?

Filler particles align with the melt flow during moulding, so heat travels faster along the flow direction than across it. Design must account for this anisotropy.

Q5: Do conductive grades still pass flammability requirements?

Many do, but filler content affects UL94 performance. Verify the rating on the specific grade, especially for EV and electrical applications.

Evaluating thermal management options? Contact NAGOMER for material guidance and machined samples before you commit to tooling.

────────────────────────────────────────

NAGOMER — Professional Engineering Plastics Solutions

www.nagomer.com  |  info@nagomer.com

滚动至顶部

Inquiry form